No product in cart
NXT Level Plus
- Add your review
NXT Level Plus is a high quality, cement-based, free-flowing underlayment for use in leveling interior substrates. Rapid setting formula produces a flat, smooth and hard surface for the installation of finished flooring. NXT Level Plus can be placed from 1/8–1 1/4" (3–32 mm) in a single lift. Suitable Substrates (Interior Only) Concrete Vinyl Tile Cement Terrazzo […]
NXT Level Plus is a high quality, cement-based, free-flowing underlayment for use in leveling interior substrates. Rapid setting formula produces a flat, smooth and hard surface for the installation of finished flooring. NXT Level Plus can be placed from 1/8–1 1/4" (3–32 mm) in a single lift.
Suitable Substrates (Interior Only)
Exterior Glue Plywood
Ceramic Tile and Stone
Cement Mortar Bed
Cement Backer Board*
Superior compressive strength formulation
Easy to use and fast setting
Inorganic; will not contribute to mold/mildew growth
Suitable surface for most finished floor goods
Can be applied directly over concrete testing at RH of 95% or less per ASTM F2170
Long heal times for extended workability
Water resistant, low-shrinking
Pumpable, free-flowing; reduces sanding and troweling
Compatible with most adhesives
55 lb (25 kg) bag/40 bags per pallet
Per 55 lb (25 kg) bag
|Nominal thickness||Approximate coverage|
|1/8" (3mm)||49 sq ft (4.6 m sq)|
|1/4" (6mm)||24 sq ft (2.3 m sq)|
|1/2" (12mm)||12 sq ft (1.1 m sq)|
|3/4" (18mm)||8.1 sq ft (0.8 m sq)|
|1" (25mm)||6.1 sq ft (0.6 m sq)|
|1 1/4" (32mm)||4.9 sq ft (0.5 m sq)|
Factory sealed containers of this product are guaranteed to be of first quality for one (1) year* if stored off the ground in a dry area.
Do not install NXT™ Level Plus over particleboard, chipboard, hardboard (Masonite®), Luan panels, asbestos, gypsum-based patching materials, asphalt, coal tar, or lightweight insulating concrete or any other dimensionally unstable materials.
NXT Level Plus is not recommended for steel-wheeled traffic.
For interior use only.
Do not install when surface temperature is below 40°F (4°C) or above 90°F (32°C).
Do not install over painted surfaces.
Do not exceed recommended mixing ratio as indicated in mixing instructions. Over watering will weaken product properties.
Never mix with cement or admixtures.
Do not apply NXT Level Plus over waterproofing or crack isolation membranes.
Adhesives/mastics, mortars and grouts for ceramic tile, pavers, brick and stone are not replacements for waterproofing membranes. When a waterproofing membrane is required, use a LATICRETE® Waterproofing Membrane on top of the dry NXT Level Plus.
Not for use in submerged applications.
Not for use as a wear surface.
Note: Substrate deflection under all live, dead and impact loads, including concentrated loads, shall comply with applicable building code and finish floor manufacturer requirements.
Read and understand the Product Data Sheet and Material Safety Data Sheet.
Consult MSDS for more safety information.
Protect finished work from traffic until fully cured.
Contains portland cement and silica sand. May irritate eyes and skin. Avoid contact with eyes or prolonged contact with skin. In case of contact, flush thoroughly with water.
Do not take internally. Silica sand may cause cancer or serious lung problems. Avoid breathing dust. Wear a respirator in dusty areas.
Keep out of reach of children.
Specifications are subject to change without notification. Technical data shown in LATICRETE product data sheets and technical data sheets are typical but reflect laboratory test procedures conducted in
laboratory conditions. Actual field performance and test results will depend on installation methods and site conditions. Field test results will vary due to critical job site factors.
|Pour depth||1/8" to 1 1/4" (3 – 32mm). Consult technical services for depths over 1.25"|
|Walkable||1 – 4 hours at 70 degrees F (21 degrees C)|
|Tensile bond strength||270 – 390 psi (1.9 – 2.7 MPa)|
|Flexural strength – 28 day cure||840 – 1100 psi ( 5.8 – 7.6 MPa)|
|Compressive strength – 28 day cure||4400 psi (30.3 MPa)|
Initial @ 20 – 30 minutes
Final @ 35 – 40 minutes
|Installed dry weight (per square foot @ 1/4" (6mm)||2.3 – 2.5 lbs / sq ft|
There are no reviews yet.